Skip to Content
/Upcycled Crafts/Denim Reversible Belt

Denim Reversible Belt

Denim Reversible Belt

denim belt pattern

So, you have seen the denim vest and the denim skirt refashioned from an outgrown denim dress in my recent 2 tutorials. Today, the third tutorial in the series is about sewing a reversible double-ring denim belt. The material of this denim belt was originally the bottom hem salvaged from the denim dress.

Not only skirt, but you can also get pants’ hems to make this reversible belt too. Just join both hems to make them into 1 long strip and continue the rest of the sewing according to this tutorial.

sew reversible denim belt
 

Denim Belt

Materials:
1. Denim/jeans dress, or any denim skirt, need only the bottom hem
2. Seam ripper
3. Strong thread for denim sewing, find the closest thread color
4. 2″ x 36″ (approx.) the length depends on how wide your hem is.
5. 1″ belt ring, 2 pcs., can be rectangle-ring or D-ring.

Tools:
1. Sewing machine
2. Denim sewing needle #16 or #18
3. Matching color threads
4. Sewing kits and pins
5. Scissors
6. Rotary cutter, quilter’s ruler & rubber mat (optional)

 
recycle skirt hem

Cut the hem above the sewing line. If it is a double fold hem, avoid cutting the fold.
Cut the hem’s seam at the back portion of the skirt so that the hem can be opened into a strip. You might not need the whole length of the hem if needed, cut to your preferred measurement.
Unpick all the stitches and press hem open flat.

 
recycle denim belt material

Cut 2″ wide of new fabric strip with the same length of the hem.
Since the ring is 1″ wide, the belt is going to be 1″ wide too. Adjust the measurement to suit your belt ring if you want to make a wider denim belt.

 
clip corner

Fold and press one of the long edges 1/2″ on the new fabric and hem. If you hem was a double folded, you can use the original fold of the denim hem.
Sew the short edge with 1/2″ seam allowance.
Sew along the long edge with 1/2″ seam allowance too.
Follow by another short seam on the side.
Clip the corners.

 
top stitch

Fold the corners in and turn the belt right side out for both corners.
Adjust the corners so they are at a nice right-angle.
[Tips: use a knitting needle or something pointy but blunt to push the corner from the inside.]

 
sew denim belt

Pin the un-sewn long edges together and topstitch near the edge. Put a little attention when sewing it, since the hem is a little curvy due to the A-line skirt construction, you might have to stretch the new fabric a little so that it follows the curve and matches the length of the hem.
Topstitch around the edges and finish off with a centerline.

 
 sew double ring buckle ring belt

Insert the denim belt ends into the rings, fold 1″ and sew 2 lines across to hold the rings in place.
If you find sewing this thick pile of fabric is difficult, try the following method that I have mentioned in the denim skirt tutorial. There is a photo to show how to do it too.
“When you are about to sew a thick pile of fabric, with the needle down and presser foot up, insert the cardboard behind the needle. Drop the foot and continue sewing. Sewing from thick to thin layer fabric has a lesser problem, if needed, just place the cardboard to the front part of the presser foot to level it and sew slowly until the needle is about to reach the cardboard. Adjust the cardboard to the front and repeat again if needed.”

 
sew reversible denim belt

SUBSCRIBE TO NEWSLETTER

Subscribe via email for latest updates:

FOLLOW CRAFT PASSION’S

Upcycle Dress To Denim Skirt
← Read Last Post
Sew Denim Rosette Brooch
Read Next Post →